Partial local dtim in lsu configuration.

pipelined/config/rv32gc/wally-config.vh

@@ -49,7 +49,7 @@
 `define UARCH_PIPELINED 1
 `define UARCH_SUPERSCALR 0
 `define UARCH_SINGLECYCLE 0
-`define MEM_DTIM 1
+`define MEM_DTIM 0
 `define MEM_DCACHE 1
 `define MEM_IROM 1
 `define MEM_ICACHE 1

pipelined/config/rv32ic/wally-config.vh

@@ -49,10 +49,10 @@
 `define UARCH_PIPELINED 1
 `define UARCH_SUPERSCALR 0
 `define UARCH_SINGLECYCLE 0
-`define MEM_DTIM 1
+`define MEM_DTIM 0
 `define MEM_DCACHE 0
-`define MEM_IROM 1
+`define MEM_IROM 0
-`define MEM_ICACHE 0
+`define MEM_ICACHE 1
 `define MEM_VIRTMEM 0
 `define VECTORED_INTERRUPTS_SUPPORTED 1 
 

pipelined/config/rv64gc/wally-config.vh

@@ -50,7 +50,7 @@
 `define UARCH_PIPELINED 1
 `define UARCH_SUPERSCALR 0
 `define UARCH_SINGLECYCLE 0
-`define MEM_DTIM 1
+`define MEM_DTIM 0
 `define MEM_DCACHE 1
 `define MEM_IROM 1
 `define MEM_ICACHE 1

pipelined/src/ifu/ifu.sv

@@ -271,7 +271,7 @@ module ifu (
 	  assign ICacheFetchLine = 0;
 	  assign ICacheBusAdr = 0;
 	  assign ICacheStallF = 0;
-	  assign FinalInstrRawF = 0;
+	  if(!`MEM_IROM) assign FinalInstrRawF = 0;
       assign ICacheAccess = CacheableF;
       assign ICacheMiss = CacheableF;
 	end
@@ -283,7 +283,22 @@ module ifu (
 				.s(SelUncachedAdr),
 				.y(InstrRawF));
 
-  // always present
+
+  if (`MEM_IROM == 1) begin : irom
+    ram #(
+        .BASE(`RAM_BASE), .RANGE(`RAM_RANGE)) ram (
+        .HCLK(clk), .HRESETn(~reset), 
+        .HSELRam(1'b1), .HADDR(PCPF[31:0]),
+        .HWRITE(1'b0), .HREADY(1'b1),
+        .HTRANS(2'b10), .HWDATA(0), .HREADRam(FinalInstrRawF),
+        .HRESPRam(), .HREADYRam());
+
+    assign BusStall = 0;
+    assign IFUBusRead = 0;
+    assign ICacheBusAck = 0;
+    assign SelUncachedAdr = 0;
+    
+  end else begin : bus
       genvar 			   index;
       for (index = 0; index < WORDSPERLINE; index++) begin:fetchbuffer
         flopen #(`XLEN) fb(.clk(clk),
@@ -303,6 +318,7 @@ module ifu (
 		     .BusStall, .LSUBusWrite(), .LSUBusRead(IFUBusRead), .DCacheBusAck(ICacheBusAck),
 		     .BusCommittedM(), .SelUncachedAdr(SelUncachedAdr), .WordCount);
 
+    end
   assign IFUStallF = ICacheStallF | BusStall | SelNextSpill;
   assign CPUBusy = StallF & ~SelNextSpill;
 

pipelined/src/lsu/lsu.sv

@@ -316,7 +316,7 @@ module lsu
 			.CacheFetchLine(DCacheFetchLine), .CacheWriteLine(DCacheWriteLine), .CacheBusAck(DCacheBusAck), .InvalidateCacheM(1'b0));
 
   end else begin : passthrough
-    assign ReadDataWordM = 0;
+    if(!`MEM_DTIM) assign ReadDataWordM = 0;
     assign DCacheStall = 0;
     assign DCacheMiss = CacheableM;
     assign DCacheAccess = CacheableM;
@@ -357,6 +357,26 @@ module lsu
 			    .HWDATAIN(FinalAMOWriteDataM),
 			    .HWDATA(FinalWriteDataM));
 
+
+  if (`MEM_DTIM == 1) begin : dtim
+    ram #(
+        .BASE(`RAM_BASE), .RANGE(`RAM_RANGE)) ram (
+        .HCLK(clk), .HRESETn(~reset), 
+        .HSELRam(1'b1), .HADDR(LSUPAdrM[31:0]),
+        .HWRITE(LSURWM[0]), .HREADY(1'b1),
+        .HTRANS(|LSURWM ? 2'b10 : 2'b00), .HWDATA(FinalWriteDataM), .HREADRam(ReadDataWordM),
+        .HRESPRam(), .HREADYRam());
+
+    // since we have a local memory the bus connections are all disabled.
+    // There are no peripherals supported.
+    assign BusStall = 0;
+    assign LSUBusWrite = 0;
+    assign LSUBusRead = 0;
+    assign DCacheBusAck = 0;
+    assign BusCommittedM = 0;
+    assign SelUncachedAdr = 0;
+    
+  end else begin : bus
     // Bus Side logic
     // register the fetch data from the next level of memory.
     // This register should be necessary for timing.  There is no register in the uncore or
@@ -386,6 +406,7 @@ module lsu
     busfsm(.clk, .reset, .IgnoreRequest, .LSURWM, .DCacheFetchLine, .DCacheWriteLine,
 		   .LSUBusAck, .CPUBusy, .CacheableM, .BusStall, .LSUBusWrite, .LSUBusRead,
 		   .DCacheBusAck, .BusCommittedM, .SelUncachedAdr, .WordCount);
+  end
     
 endmodule
 

pipelined/src/uncore/ram.sv

@@ -56,6 +56,8 @@ module ram #(parameter BASE=0, RANGE = 65535) (
 
   if(`FPGA) begin:ram
     initial begin
+      // *** need to address this preload for fpga.  It should work as a preload file
+      // but for some reason vivado is not synthesizing the preload.
       //$readmemh(PRELOAD, RAM);
       RAM[0] =  64'h94e1819300002197;
       RAM[1] =  64'h4281420141014081;

pipelined/testbench/testbench.sv

@@ -196,6 +196,7 @@ logic [3:0] dummy;
       else pathname = tvpaths[1]; */
       memfilename = {pathname, tests[test], ".elf.memfile"};
       $readmemh(memfilename, dut.uncore.ram.ram.RAM);
+      //if(`MEM_DTIM == 1) $readmemh(memfilename, dut.hart.lsu.dtim.ram.RAM);
       ProgramAddrMapFile = {pathname, tests[test], ".elf.objdump.addr"};
       ProgramLabelMapFile = {pathname, tests[test], ".elf.objdump.lab"};
       $display("Read memfile %s", memfilename);
@@ -249,6 +250,7 @@ logic [3:0] dummy;
           //$display("signature[%h] = %h", i, signature[i]);
 		  // *** have to figure out how to exclude shadowram when not using a dcache.
           if (signature[i] !== dut.uncore.ram.ram.RAM[testadr+i] &
+          //if (signature[i] !== dut.hart.lsu.dtim.ram.RAM[testadr+i] &
 	      (signature[i] !== DCacheFlushFSM.ShadowRAM[testadr+i])) begin
             if (signature[i+4] !== 'bx | signature[i] !== 32'hFFFFFFFF) begin
               // report errors unless they are garbage at the end of the sim
@@ -256,6 +258,7 @@ logic [3:0] dummy;
               errors = errors+1;
               $display("  Error on test %s result %d: adr = %h sim (D$) %h sim (TIM) = %h, signature = %h", 
                     tests[test], i, (testadr+i)*(`XLEN/8), DCacheFlushFSM.ShadowRAM[testadr+i], dut.uncore.ram.ram.RAM[testadr+i], signature[i]);
+                    //   tests[test], i, (testadr+i)*(`XLEN/8), DCacheFlushFSM.ShadowRAM[testadr+i], dut.hart.lsu.dtim.ram.RAM[testadr+i], signature[i]);
               $stop;//***debug
             end
           end
@@ -279,6 +282,7 @@ logic [3:0] dummy;
             //pathname = tvpaths[tests[0]];
             memfilename = {pathname, tests[test], ".elf.memfile"};
             $readmemh(memfilename, dut.uncore.ram.ram.RAM);
+            //if(`MEM_DTIM == 1) $readmemh(memfilename, dut.hart.lsu.dtim.ram.RAM);
             ProgramAddrMapFile = {pathname, tests[test], ".elf.objdump.addr"};
             ProgramLabelMapFile = {pathname, tests[test], ".elf.objdump.lab"};
             $display("Read memfile %s", memfilename);