cvw/pipelined/src/uncore/gpio_apb.sv

///////////////////////////////////////////
// gpio_apb.sv
//
// Written: David_Harris@hmc.edu 14 January 2021
// Modified: bbracker@hmc.edu 15 Apr. 2021
//
// Purpose: General Purpose I/O peripheral
//   See FE310-G002-Manual-v19p05 for specifications
//   No interrupts, drive strength, or pull-ups supported
// 
// A component of the Wally configurable RISC-V project.
// 
// Copyright (C) 2021 Harvey Mudd College & Oklahoma State University
//
// MIT LICENSE
// Permission is hereby granted, free of charge, to any person obtaining a copy of this 
// software and associated documentation files (the "Software"), to deal in the Software 
// without restriction, including without limitation the rights to use, copy, modify, merge, 
// publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons 
// to whom the Software is furnished to do so, subject to the following conditions:
//
//   The above copyright notice and this permission notice shall be included in all copies or 
//   substantial portions of the Software.
//
//   THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, 
//   INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR 
//   PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS 
//   BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, 
//   TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE 
//   OR OTHER DEALINGS IN THE SOFTWARE.
////////////////////////////////////////////////////////////////////////////////////////////////

`include "wally-config.vh"

module gpio_apb (
  input  logic             PCLK, PRESETn,
  input  logic             PSEL,
  input  logic [7:0]       PADDR, 
  input  logic [`XLEN-1:0] PWDATA,
  input  logic             PWRITE,
  input  logic             PENABLE,
  output logic [`XLEN-1:0] PRDATA,
  output logic             PREADY,
  input  logic [31:0]      GPIOPinsIn,
  output logic [31:0]      GPIOPinsOut, GPIOPinsEn,
  output logic             GPIOIntr);

  logic [31:0] input0d, input1d, input2d, input3d;
  logic [31:0] input_val, input_en, output_en, output_val;
  logic [31:0] rise_ie, rise_ip, fall_ie, fall_ip, high_ie, high_ip, low_ie, low_ip; 

  logic [7:0] entry;
  logic [31:0] Din, Dout;
  logic memwrite;
  
  // APB I/O
  assign entry = {PADDR[7:2],2'b00};  // 32-bit word-aligned accesses
  assign memwrite = PWRITE & PENABLE;  // only write in access phase
  assign PREADY = PENABLE; // GPIO never takes >1 cycle to respond

  // account for subword read/write circuitry
  // -- Note GPIO registers are 32 bits no matter what; access them with LW SW.
  //    (At least that's what I think when FE310 spec says "only naturally aligned 32-bit accesses are supported")
  if (`XLEN == 64) begin
    assign Din =    entry[2] ? PWDATA[63:32] : PWDATA[31:0];
    assign PRDATA = entry[2] ? {Dout,32'b0}  : {32'b0,Dout};
  end else begin // 32-bit
    assign Din = PWDATA[31:0];
    assign PRDATA = Dout;
  end

  // register access
  always_ff @(posedge PCLK, negedge PRESETn)
    if (~PRESETn) begin // asynch reset
      input_en <= 0;
      output_en <= 0;
      // *** synch reset not yet implemented [DH: can we delete this comment?  Check if a sync reset is required]
      output_val <= #1 0;
      rise_ie <= #1 0;
      rise_ip <= #1 0;
      fall_ie <= #1 0;
      fall_ip <= #1 0;
      high_ie <= #1 0;
      high_ip <= #1 0;
      low_ie <= #1 0;
      low_ip <= #1 0;
    end else begin     // writes
        // According to FE310 spec: Once the interrupt is pending, it will remain set until a 1 is written to the *_ip register at that bit.
        /* verilator lint_off CASEINCOMPLETE */
      if (memwrite) 
        case(entry)
          8'h04: input_en <= #1 Din;
          8'h08: output_en <= #1 Din;
          8'h0C: output_val <= #1 Din;
          8'h18: rise_ie <= #1 Din;
          8'h20: fall_ie <= #1 Din;
          8'h28: high_ie <= #1 Din;
          8'h30: low_ie  <= #1 Din;
          8'h40: output_val <= #1 output_val ^ Din; // OUT_XOR
        endcase
        /* verilator lint_on CASEINCOMPLETE */

      // interrupts can be cleared by writing corresponding bits to a register
      if (memwrite & entry == 8'h1C)   rise_ip <= rise_ip & ~Din;
      else                             rise_ip <= rise_ip | (input2d & ~input3d);
      if (memwrite & (entry == 8'h24)) fall_ip <= fall_ip & ~Din;
      else                             fall_ip <= fall_ip | (~input2d & input3d);
      if (memwrite & (entry == 8'h2C)) high_ip <= high_ip & ~Din;
      else                             high_ip <= high_ip | input3d;
      if (memwrite & (entry == 8'h34)) low_ip  <= low_ip  & ~Din;
      else                             low_ip  <= low_ip  | ~input3d;

      case(entry) // flop to sample inputs
        8'h00: Dout <= #1 input_val;
        8'h04: Dout <= #1 input_en;
        8'h08: Dout <= #1 output_en;
        8'h0C: Dout <= #1 output_val;
        8'h18: Dout <= #1 rise_ie;
        8'h1C: Dout <= #1 rise_ip;
        8'h20: Dout <= #1 fall_ie;
        8'h24: Dout <= #1 fall_ip;
        8'h28: Dout <= #1 high_ie;
        8'h2C: Dout <= #1 high_ip;
        8'h30: Dout <= #1 low_ie;
        8'h34: Dout <= #1 low_ip;
        8'h40: Dout <= #1 0; // OUT_XOR reads as 0
        default: Dout <= #1 0;
      endcase
    end

  // chip i/o
  // connect OUT to IN for loopback testing
  if (`GPIO_LOOPBACK_TEST) assign input0d = ((output_en & GPIOPinsOut) | (~output_en & GPIOPinsIn)) & input_en;
  else                     assign input0d = GPIOPinsIn & input_en;

  // synchroninzer for inputs
  flop #(32) sync1(PCLK,input0d,input1d);
  flop #(32) sync2(PCLK,input1d,input2d);
  flop #(32) sync3(PCLK,input2d,input3d);
  assign input_val = input3d;
  assign GPIOPinsOut = output_val;
  assign GPIOPinsEn = output_en;

  assign GPIOIntr = |{(rise_ip & rise_ie),(fall_ip & fall_ie),(high_ip & high_ie),(low_ip & low_ie)};
endmodule