///////////////////////////////////////////
// testbench.sv
//
// Written: David_Harris@hmc.edu 9 January 2021
// Modified:
//
// Purpose: Wally Testbench and helper modules
// Applies test programs from the riscv-arch-test and Imperas suites
//
// A component of the Wally configurable RISC-V project.
//
// Copyright (C) 2021 Harvey Mudd College & Oklahoma State University
//
// SPDX-License-Identifier: Apache-2.0 WITH SHL-2.1
//
// Licensed under the Solderpad Hardware License v 2.1 (the “License”); you may not use this file
// except in compliance with the License, or, at your option, the Apache License version 2.0. You
// may obtain a copy of the License at
//
// https://solderpad.org/licenses/SHL-2.1/
//
// Unless required by applicable law or agreed to in writing, any work distributed under the
// License is distributed on an “AS IS” BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND,
// either express or implied. See the License for the specific language governing permissions
// and limitations under the License.
////////////////////////////////////////////////////////////////////////////////////////////////
`include "config.vh"
`include "tests.vh"
`include "BranchPredictorType.vh"
import cvw::*;
module testbench;
/* verilator lint_off WIDTHTRUNC */
/* verilator lint_off WIDTHEXPAND */
parameter DEBUG=0;
parameter TEST="none";
parameter PrintHPMCounters=0;
parameter BPRED_LOGGER=1;
parameter I_CACHE_ADDR_LOGGER=0;
parameter D_CACHE_ADDR_LOGGER=0;
`include "parameter-defs.vh"
logic clk;
logic reset_ext, reset;
logic ResetMem;
// DUT signals
logic [P.AHBW-1:0] HRDATAEXT;
logic HREADYEXT, HRESPEXT;
logic HSELEXTSDC;
logic [P.PA_BITS-1:0] HADDR;
logic [P.AHBW-1:0] HWDATA;
logic [P.XLEN/8-1:0] HWSTRB;
logic HWRITE;
logic [2:0] HSIZE;
logic [2:0] HBURST;
logic [3:0] HPROT;
logic [1:0] HTRANS;
logic HMASTLOCK;
logic HCLK, HRESETn;
logic [31:0] GPIOIN, GPIOOUT, GPIOEN;
logic UARTSin, UARTSout;
logic SPIIn, SPIOut;
logic [3:0] SPICS;
logic SDCIntr;
logic HREADY;
logic HSELEXT;
string ProgramAddrMapFile, ProgramLabelMapFile;
integer ProgramAddrLabelArray [string];
int test, i, errors, totalerrors;
string outputfile;
integer outputFilePointer;
string tests[];
logic DCacheFlushDone, DCacheFlushStart;
logic riscofTest;
logic Validate;
logic SelectTest;
// pick tests based on modes supported
initial begin
$display("TEST is %s", TEST);
//tests = '{};
if (P.XLEN == 64) begin // RV64
case (TEST)
"arch64i": tests = arch64i;
"arch64priv": tests = arch64priv;
"arch64c": if (P.C_SUPPORTED)
if (P.ZICSR_SUPPORTED) tests = {arch64c, arch64cpriv};
else tests = {arch64c};
"arch64m": if (P.M_SUPPORTED) tests = arch64m;
"arch64a": if (P.A_SUPPORTED) tests = arch64a;
"arch64f": if (P.F_SUPPORTED) tests = arch64f;
"arch64d": if (P.D_SUPPORTED) tests = arch64d;
"arch64f_fma": if (P.F_SUPPORTED) tests = arch64f_fma;
"arch64d_fma": if (P.D_SUPPORTED) tests = arch64d_fma;
"arch64zi": if (P.ZIFENCEI_SUPPORTED) tests = arch64zi;
"imperas64i": tests = imperas64i;
"imperas64f": if (P.F_SUPPORTED) tests = imperas64f;
"imperas64d": if (P.D_SUPPORTED) tests = imperas64d;
"imperas64m": if (P.M_SUPPORTED) tests = imperas64m;
"wally64a": if (P.A_SUPPORTED) tests = wally64a;
"imperas64c": if (P.C_SUPPORTED) tests = imperas64c;
else tests = imperas64iNOc;
"custom": tests = custom;
"wally64i": tests = wally64i;
"wally64priv": tests = wally64priv;
"wally64periph": tests = wally64periph;
"coremark": tests = coremark;
"fpga": tests = fpga;
"ahb" : tests = ahb;
"coverage64gc" : tests = coverage64gc;
"arch64zba": if (P.ZBA_SUPPORTED) tests = arch64zba;
"arch64zbb": if (P.ZBB_SUPPORTED) tests = arch64zbb;
"arch64zbc": if (P.ZBC_SUPPORTED) tests = arch64zbc;
"arch64zbs": if (P.ZBS_SUPPORTED) tests = arch64zbs;
endcase
end else begin // RV32
case (TEST)
"arch32i": tests = arch32i;
"arch32priv": tests = arch32priv;
"arch32c": if (P.C_SUPPORTED)
if (P.ZICSR_SUPPORTED) tests = {arch32c, arch32cpriv};
else tests = {arch32c};
"arch32m": if (P.M_SUPPORTED) tests = arch32m;
"arch32a": if (P.A_SUPPORTED) tests = arch32a;
"arch32f": if (P.F_SUPPORTED) tests = arch32f;
"arch32d": if (P.D_SUPPORTED) tests = arch32d;
"arch32f_fma": if (P.F_SUPPORTED) tests = arch32f_fma;
"arch32d_fma": if (P.D_SUPPORTED) tests = arch32d_fma;
"arch32zi": if (P.ZIFENCEI_SUPPORTED) tests = arch32zi;
"imperas32i": tests = imperas32i;
"imperas32f": if (P.F_SUPPORTED) tests = imperas32f;
"imperas32m": if (P.M_SUPPORTED) tests = imperas32m;
"wally32a": if (P.A_SUPPORTED) tests = wally32a;
"imperas32c": if (P.C_SUPPORTED) tests = imperas32c;
else tests = imperas32iNOc;
"wally32i": tests = wally32i;
"wally32e": tests = wally32e;
"wally32priv": tests = wally32priv;
"wally32periph": tests = wally32periph;
"embench": tests = embench;
"coremark": tests = coremark;
"arch32zba": if (P.ZBA_SUPPORTED) tests = arch32zba;
"arch32zbb": if (P.ZBB_SUPPORTED) tests = arch32zbb;
"arch32zbc": if (P.ZBC_SUPPORTED) tests = arch32zbc;
"arch32zbs": if (P.ZBS_SUPPORTED) tests = arch32zbs;
endcase
end
if (tests.size() == 0) begin
$display("TEST %s not supported in this configuration", TEST);
$stop;
end
end // initial begin
// Model the testbench as an fsm.
// Do this in parts so it easier to verify
// part 1: build a version which echos the same behavior as the below code, but does not drive anything
// part 2: drive some of the controls
// part 3: drive all logic and remove old inital and always @ negedge clk block
typedef enum logic [3:0]{STATE_TESTBENCH_RESET,
STATE_INIT_TEST,
STATE_RESET_MEMORIES,
STATE_RESET_MEMORIES2,
STATE_LOAD_MEMORIES,
STATE_RESET_TEST,
STATE_RUN_TEST,
STATE_CHECK_TEST,
STATE_CHECK_TEST_WAIT,
STATE_VALIDATE,
STATE_INCR_TEST} statetype;
statetype CurrState, NextState;
logic TestBenchReset;
logic [2:0] ResetCount, ResetThreshold;
logic LoadMem;
logic ResetCntEn;
logic ResetCntRst;
string signame, memfilename, pathname;
integer begin_signature_addr;
assign ResetThreshold = 3'd5;
initial begin
TestBenchReset = 1;
# 100;
TestBenchReset = 0;
end
always_ff @(posedge clk)
if (TestBenchReset) CurrState <= #1 STATE_TESTBENCH_RESET;
else CurrState <= #1 NextState;
// fsm next state logic
always_comb begin
// riscof tests have a different signature, tests[0] == "1" refers to RiscvArchTests
// and tests[0] == "2" refers to WallyRiscvArchTests
riscofTest = tests[0] == "1" | tests[0] == "2";
pathname = tvpaths[tests[0].atoi()];
case(CurrState)
STATE_TESTBENCH_RESET: NextState = STATE_INIT_TEST;
STATE_INIT_TEST: NextState = STATE_RESET_MEMORIES;
STATE_RESET_MEMORIES: NextState = STATE_RESET_MEMORIES2;
STATE_RESET_MEMORIES2: NextState = STATE_LOAD_MEMORIES; // Give the reset enough time to ensure the bus is reset before loading the memories.
STATE_LOAD_MEMORIES: NextState = STATE_RESET_TEST;
STATE_RESET_TEST: if(ResetCount < ResetThreshold) NextState = STATE_RESET_TEST;
else NextState = STATE_RUN_TEST;
STATE_RUN_TEST: if(DCacheFlushStart) NextState = STATE_CHECK_TEST;
else NextState = STATE_RUN_TEST;
STATE_CHECK_TEST: if (DCacheFlushDone) NextState = STATE_VALIDATE;
else NextState = STATE_CHECK_TEST_WAIT;
STATE_CHECK_TEST_WAIT: if(DCacheFlushDone) NextState = STATE_VALIDATE;
else NextState = STATE_CHECK_TEST_WAIT;
STATE_VALIDATE: NextState = STATE_INIT_TEST;
STATE_INCR_TEST: NextState = STATE_INIT_TEST;
default: NextState = STATE_TESTBENCH_RESET;
endcase
end // always_comb
// fsm output control logic
assign reset_ext = CurrState == STATE_TESTBENCH_RESET | CurrState == STATE_INIT_TEST |
CurrState == STATE_RESET_MEMORIES | CurrState == STATE_RESET_MEMORIES2 |
CurrState == STATE_LOAD_MEMORIES | CurrState ==STATE_RESET_TEST;
// this initialization is very expensive, only do it for coremark.
assign ResetMem = (CurrState == STATE_RESET_MEMORIES | CurrState == STATE_RESET_MEMORIES2) & TEST == "coremark";
assign LoadMem = CurrState == STATE_LOAD_MEMORIES;
assign ResetCntRst = CurrState == STATE_INIT_TEST;
assign ResetCntEn = CurrState == STATE_RESET_TEST;
assign Validate = CurrState == STATE_VALIDATE;
assign SelectTest = CurrState == STATE_INIT_TEST;
// fsm reset counter
counter #(3) RstCounter(clk, ResetCntRst, ResetCntEn, ResetCount);
////////////////////////////////////////////////////////////////////////////////
// Find the test vector files and populate the PC to function label converter
////////////////////////////////////////////////////////////////////////////////
logic [P.XLEN-1:0] testadr;
assign begin_signature_addr = ProgramAddrLabelArray["begin_signature"];
always @(posedge clk) begin
if(SelectTest) begin
if (riscofTest) memfilename = {pathname, tests[test], "/ref/ref.elf.memfile"};
else memfilename = {pathname, tests[test], ".elf.memfile"};
if (riscofTest) begin
ProgramAddrMapFile = {pathname, tests[test], "/ref/ref.elf.objdump.addr"};
ProgramLabelMapFile = {pathname, tests[test], "/ref/ref.elf.objdump.lab"};
end else begin
ProgramAddrMapFile = {pathname, tests[test], ".elf.objdump.addr"};
ProgramLabelMapFile = {pathname, tests[test], ".elf.objdump.lab"};
end
// declare memory labels that interest us, the updateProgramAddrLabelArray task will find
// the addr of each label and fill the array. To expand, add more elements to this array
// and initialize them to zero (also initilaize them to zero at the start of the next test)
updateProgramAddrLabelArray(ProgramAddrMapFile, ProgramLabelMapFile, ProgramAddrLabelArray);
end
////////////////////////////////////////////////////////////////////////////////
// Verify the test ran correctly by checking the memory against a known signature.
////////////////////////////////////////////////////////////////////////////////
if(TestBenchReset) test = 1;
if (TEST == "coremark")
if (dut.core.EcallFaultM) begin
$display("Benchmark: coremark is done.");
$stop;
end
if(Validate) begin
if (TEST == "embench") begin
// Writes contents of begin_signature to .sim.output file
// this contains instret and cycles for start and end of test run, used by embench
// python speed script to calculate embench speed score.
// also, begin_signature contains the results of the self checking mechanism,
// which will be read by the python script for error checking
$display("Embench Benchmark: %s is done.", tests[test]);
if (riscofTest) outputfile = {pathname, tests[test], "/ref/ref.sim.output"};
else outputfile = {pathname, tests[test], ".sim.output"};
outputFilePointer = $fopen(outputfile, "w");
i = 0;
testadr = ($unsigned(begin_signature_addr))/(P.XLEN/8);
while ($unsigned(i) < $unsigned(5'd5)) begin
$fdisplayh(outputFilePointer, DCacheFlushFSM.ShadowRAM[testadr+i]);
i = i + 1;
end
$fclose(outputFilePointer);
$display("Embench Benchmark: created output file: %s", outputfile);
end else if (TEST == "coverage64gc") begin
$display("Coverage tests don't get checked");
end else begin
// for tests with no self checking mechanism, read .signature.output file and compare to check for errors
// clear signature to prevent contamination from previous tests
end
if (!begin_signature_addr)
$display("begin_signature addr not found in %s", ProgramLabelMapFile);
else if (TEST != "embench") begin // *** quick hack for embench. need a better long term solution
CheckSignature(pathname, tests[test], riscofTest, begin_signature_addr, errors);
end
if(errors > 0) totalerrors = totalerrors + 1;
test = test + 1; // *** this probably needs to be moved.
if (test == tests.size()) begin
if (totalerrors == 0) $display("SUCCESS! All tests ran without failures.");
else $display("FAIL: %d test programs had errors", totalerrors);
$stop;
end
end
end
////////////////////////////////////////////////////////////////////////////////
// Some memories are not reset, but should be zeros or set to some initial value for simulation
////////////////////////////////////////////////////////////////////////////////
integer adrindex;
always @(posedge clk) begin
if (ResetMem) // program memory is sometimes reset
if (P.UNCORE_RAM_SUPPORTED)
for (adrindex=0; adrindex<(P.UNCORE_RAM_RANGE>>1+(P.XLEN/32)); adrindex = adrindex+1)
dut.uncore.uncore.ram.ram.memory.RAM[adrindex] = '0;
if(reset) begin // branch predictor must always be reset
if (P.BPRED_SUPPORTED) begin
// local history only
if (P.BPRED_TYPE == `BP_LOCAL_AHEAD | P.BPRED_TYPE == `BP_LOCAL_REPAIR)
for(adrindex = 0; adrindex < 2**P.BPRED_NUM_LHR; adrindex++)
dut.core.ifu.bpred.bpred.Predictor.DirPredictor.BHT.mem[adrindex] = 0;
for(adrindex = 0; adrindex < 2**P.BTB_SIZE; adrindex++)
dut.core.ifu.bpred.bpred.TargetPredictor.memory.mem[adrindex] = 0;
for(adrindex = 0; adrindex < 2**P.BPRED_SIZE; adrindex++)
dut.core.ifu.bpred.bpred.Predictor.DirPredictor.PHT.mem[adrindex] = 0;
end
end
end
////////////////////////////////////////////////////////////////////////////////
// load memories with program image
////////////////////////////////////////////////////////////////////////////////
always @(posedge clk) begin
if (LoadMem) begin
if (P.SDC_SUPPORTED) begin
string romfilename, sdcfilename;
romfilename = {"../tests/custom/fpga-test-sdc/bin/fpga-test-sdc.memfile"};
sdcfilename = {"../testbench/sdc/ramdisk2.hex"};
//$readmemh(romfilename, dut.uncore.uncore.bootrom.bootrom.memory.ROM);
//$readmemh(sdcfilename, sdcard.sdcard.FLASHmem);
// shorten sdc timers for simulation
//dut.uncore.uncore.sdc.SDC.LimitTimers = 1;
end
else if (P.IROM_SUPPORTED) $readmemh(memfilename, dut.core.ifu.irom.irom.rom.ROM);
else if (P.BUS_SUPPORTED) $readmemh(memfilename, dut.uncore.uncore.ram.ram.memory.RAM);
if (P.DTIM_SUPPORTED) $readmemh(memfilename, dut.core.lsu.dtim.dtim.ram.RAM);
$display("Read memfile %s", memfilename);
end
end
////////////////////////////////////////////////////////////////////////////////
// Actual hardware
////////////////////////////////////////////////////////////////////////////////
// instantiate device to be tested
assign GPIOIN = 0;
assign UARTSin = 1;
assign SPIIn = 0;
if(P.EXT_MEM_SUPPORTED) begin
ram_ahb #(.BASE(P.EXT_MEM_BASE), .RANGE(P.EXT_MEM_RANGE))
ram (.HCLK, .HRESETn, .HADDR, .HWRITE, .HTRANS, .HWDATA, .HSELRam(HSELEXT),
.HREADRam(HRDATAEXT), .HREADYRam(HREADYEXT), .HRESPRam(HRESPEXT), .HREADY, .HWSTRB);
end else begin
assign HREADYEXT = 1;
assign {HRESPEXT, HRDATAEXT} = '0;
end
if(P.SDC_SUPPORTED) begin : sdcard
// *** fix later
/* -----\/----- EXCLUDED -----\/-----
sdModel sdcard
(.sdClk(SDCCLK),
.cmd(SDCCmd),
.dat(SDCDat));
assign SDCCmd = SDCCmdOE ? SDCCmdOut : 1'bz;
assign SDCCmdIn = SDCCmd;
assign SDCDat = sd_dat_reg_t ? sd_dat_reg_o : sd_dat_i;
assign SDCDatIn = SDCDat;
-----/\----- EXCLUDED -----/\----- */
assign SDCIntr = '0;
end else begin
assign SDCIntr = '0;
end
wallypipelinedsoc #(P) dut(.clk, .reset_ext, .reset, .HRDATAEXT, .HREADYEXT, .HRESPEXT, .HSELEXT, .HSELEXTSDC,
.HCLK, .HRESETn, .HADDR, .HWDATA, .HWSTRB, .HWRITE, .HSIZE, .HBURST, .HPROT,
.HTRANS, .HMASTLOCK, .HREADY, .TIMECLK(1'b0), .GPIOIN, .GPIOOUT, .GPIOEN,
.UARTSin, .UARTSout, .SDCIntr, .SPIIn, .SPIOut, .SPICS);
// generate clock to sequence tests
always begin
clk = 1; # 5; clk = 0; # 5;
end
////////////////////////////////////////////////////////////////////////////////
// Support logic
////////////////////////////////////////////////////////////////////////////////
// Duplicate copy of pipeline registers that are optimized out of some configurations
logic [31:0] NextInstrE, InstrM;
mux2 #(32) FlushInstrMMux(dut.core.ifu.InstrE, dut.core.ifu.nop, dut.core.ifu.FlushM, NextInstrE);
flopenr #(32) InstrMReg(clk, reset, ~dut.core.ifu.StallM, NextInstrE, InstrM);
// Track names of instructions
string InstrFName, InstrDName, InstrEName, InstrMName, InstrWName;
logic [31:0] InstrW;
flopenr #(32) InstrWReg(clk, reset, ~dut.core.ieu.dp.StallW, InstrM, InstrW);
instrTrackerTB it(clk, reset, dut.core.ieu.dp.FlushE,
dut.core.ifu.InstrRawF[31:0],
dut.core.ifu.InstrD, dut.core.ifu.InstrE,
InstrM, InstrW,
InstrFName, InstrDName, InstrEName, InstrMName, InstrWName);
// watch for problems such as lockup, reading unitialized memory, bad configs
watchdog #(P.XLEN, 1000000) watchdog(.clk, .reset); // check if PCW is stuck
ramxdetector #(P.XLEN, P.LLEN) ramxdetector(clk, dut.core.lsu.MemRWM[1], dut.core.lsu.LSULoadAccessFaultM, dut.core.lsu.ReadDataM,
dut.core.ifu.PCM, InstrM, dut.core.lsu.IEUAdrM, InstrMName);
riscvassertions #(P) riscvassertions(); // check assertions for a legal configuration
loggers #(P, TEST, PrintHPMCounters, I_CACHE_ADDR_LOGGER, D_CACHE_ADDR_LOGGER, BPRED_LOGGER)
loggers (clk, reset, DCacheFlushStart, DCacheFlushDone, memfilename);
// track the current function or global label
if (DEBUG == 1 | ((PrintHPMCounters | BPRED_LOGGER) & P.ZICNTR_SUPPORTED)) begin : FunctionName
FunctionName #(P) FunctionName(.reset(reset_ext | TestBenchReset),
.clk(clk), .ProgramAddrMapFile(ProgramAddrMapFile), .ProgramLabelMapFile(ProgramLabelMapFile));
end
// Termination condition
// terminate on a specific ECALL after li x3,1 for old Imperas tests, *** remove this when old imperas tests are removed
// or sw gp,-56(t0) for new Imperas tests
// or sd gp, -56(t0)
// or on a jump to self infinite loop (6f) for RISC-V Arch tests
logic ecf; // remove this once we don't rely on old Imperas tests with Ecalls
if (P.ZICSR_SUPPORTED) assign ecf = dut.core.priv.priv.EcallFaultM;
else assign ecf = 0;
assign DCacheFlushStart = ecf &
(dut.core.ieu.dp.regf.rf[3] == 1 |
(dut.core.ieu.dp.regf.we3 &
dut.core.ieu.dp.regf.a3 == 3 &
dut.core.ieu.dp.regf.wd3 == 1)) |
((InstrM == 32'h6f | InstrM == 32'hfc32a423 | InstrM == 32'hfc32a823) & dut.core.ieu.c.InstrValidM ) |
((dut.core.lsu.IEUAdrM == ProgramAddrLabelArray["tohost"]) & InstrMName == "SW" );
DCacheFlushFSM #(P) DCacheFlushFSM(.clk(clk), .reset(reset), .start(DCacheFlushStart), .done(DCacheFlushDone));
task automatic CheckSignature;
// This task must be declared inside this module as it needs access to parameter P. There is
// no way to pass P to the task unless we convert it to a module.
input string pathname;
input string TestName;
input logic riscofTest;
input integer begin_signature_addr;
output integer errors;
localparam SIGNATURESIZE = 5000000;
integer i;
logic [31:0] sig32[0:SIGNATURESIZE];
logic [P.XLEN-1:0] signature[0:SIGNATURESIZE];
string signame;
logic [P.XLEN-1:0] testadr, testadrNoBase;
// for tests with no self checking mechanism, read .signature.output file and compare to check for errors
// clear signature to prevent contamination from previous tests
for(i=0; i<SIGNATURESIZE; i=i+1) begin
sig32[i] = 'bx;
end
if (riscofTest) signame = {pathname, TestName, "/ref/Reference-sail_c_simulator.signature"};
else signame = {pathname, TestName, ".signature.output"};
// read signature, reformat in 64 bits if necessary
$readmemh(signame, sig32);
i = 0;
while (i < SIGNATURESIZE) begin
if (P.XLEN == 32) begin
signature[i] = sig32[i];
i = i+1;
end else begin
signature[i/2] = {sig32[i+1], sig32[i]};
i = i + 2;
end
if (i >= 4 & sig32[i-4] === 'bx) begin
if (i == 4) begin
i = SIGNATURESIZE+1; // flag empty file
$display(" Error: empty test file");
end else i = SIGNATURESIZE; // skip over the rest of the x's for efficiency
end
end
// Check errors
errors = (i == SIGNATURESIZE+1); // error if file is empty
i = 0;
testadr = ($unsigned(begin_signature_addr))/(P.XLEN/8);
testadrNoBase = (begin_signature_addr - P.UNCORE_RAM_BASE)/(P.XLEN/8);
/* verilator lint_off INFINITELOOP */
while (signature[i] !== 'bx) begin
logic [P.XLEN-1:0] sig;
if (P.DTIM_SUPPORTED) sig = testbench.dut.core.lsu.dtim.dtim.ram.RAM[testadrNoBase+i];
else if (P.UNCORE_RAM_SUPPORTED) sig = testbench.dut.uncore.uncore.ram.ram.memory.RAM[testadrNoBase+i];
//$display("signature[%h] = %h sig = %h", i, signature[i], sig);
if (signature[i] !== sig & (signature[i] !== testbench.DCacheFlushFSM.ShadowRAM[testadr+i])) begin
errors = errors+1;
$display(" Error on test %s result %d: adr = %h sim (D$) %h sim (DTIM_SUPPORTED) = %h, signature = %h",
TestName, i, (testadr+i)*(P.XLEN/8), testbench.DCacheFlushFSM.ShadowRAM[testadr+i], sig, signature[i]);
$stop; //***debug
end
i = i + 1;
end
/* verilator lint_on INFINITELOOP */
if (errors == 0) begin
$display("%s succeeded. Brilliant!!!", TestName);
end else begin
$display("%s failed with %d errors. :(", TestName, errors);
//totalerrors = totalerrors+1;
end
endtask //
/* verilator lint_on WIDTHTRUNC */
/* verilator lint_on WIDTHEXPAND */
endmodule
/* verilator lint_on STMTDLY */
/* verilator lint_on WIDTH */
task automatic updateProgramAddrLabelArray;
/* verilator lint_off WIDTHTRUNC */
/* verilator lint_off WIDTHEXPAND */
input string ProgramAddrMapFile, ProgramLabelMapFile;
inout integer ProgramAddrLabelArray [string];
// Gets the memory location of begin_signature
integer ProgramLabelMapFP, ProgramAddrMapFP;
ProgramLabelMapFP = $fopen(ProgramLabelMapFile, "r");
ProgramAddrMapFP = $fopen(ProgramAddrMapFile, "r");
if (ProgramLabelMapFP & ProgramAddrMapFP) begin // check we found both files
// *** RT: I'm a bit confused by the required initialization here.
ProgramAddrLabelArray["begin_signature"] = 0;
ProgramAddrLabelArray["tohost"] = 0;
while (!$feof(ProgramLabelMapFP)) begin
string label, adrstr;
integer returncode;
returncode = $fscanf(ProgramLabelMapFP, "%s\n", label);
returncode = $fscanf(ProgramAddrMapFP, "%s\n", adrstr);
if (ProgramAddrLabelArray.exists(label)) ProgramAddrLabelArray[label] = adrstr.atohex();
end
end
$fclose(ProgramLabelMapFP);
$fclose(ProgramAddrMapFP);
/* verilator lint_on WIDTHTRUNC */
/* verilator lint_on WIDTHEXPAND */
endtask